top of page

Connectors

Untitled design (40).png
CD111-200x146-1.png
C53TS-Offset-3-Prong---Aug2024-(25)-Clean-Shaddow-rgb-667x500-png.png
cd115fs5-Degree-Lanyard-Adaptor-350X125.png
MicrosoftTeams-image (2).png

9 Connectors for all your design needs

Untitled design (40).png

CD103AF | Alignable Connector

Up to .6" of offset, 35 g. Ideal for use with Air-Lock and Easy-Off Locks. It can be glued to the lock in any offset position for fabrication into the socket, or keys directly onto locks when used with inserts. Eliminates the need for offset components. For laminations or thermoforming. 350 lb. weight limit.

Untitled design (79).png
CD103MDI-200X200.png

CD103MDI | Multi-Direction Insert

Up to .28" offset in two directions. Installed into connector to allow connector to be keyed onto bottom of lock in centered position or offset in two directions. For laminations or thermoforming. Use with Alignable Connector or One-Shot Connector. 

Untitled design (80).png
CD103SDI-200x200.png

CD103SDI | Single-Direction Insert

Up to .3" offset in one direction. Installed into connector to allow connector to be keyed onto bottom of lock in centered position or offset in one direction. For laminations or thermoforming. Use with Alignable Connector or One-Shot Connector. 

Untitled design (81).png

CD111 | One-Shot Connector

CD111-200x146-1.png

Up to .6" of offset, 44 g. This connector has a tie off ring for easier lay-ups. Lower profile than the Alignable Connector. The CD111 can be glued to lock in the desired location or keyed onto lock using inserts. For laminating only. 350 lb. weight limit.

Untitled design (82).png

CD119SC | Test Socket Connector

CD119SC-TestSocketConnector-200x146.png

Cost-effective connector designed specifically for Vivac check sockets. Economical, cost-effective, easy to way to glue on a connector. Connects to standard four-hole componentry with our new high strength bridging design. Bonds well with Coyote Quik Glue. Only for use in parallel bars with fiberglass wrapping. 11/16" height / 2 3/4" diamater, reusable.

Untitled design (83).png
cd115fs5-Degree-Lanyard-Adaptor-350X125.png

CD115CF5 | 5 Degree AK Connector

Capable of up to 1.5" of offset with 5 degrees of flexion angle. The 5 Degree AK Connector is used primarily with the Coyote Locking Lanyard CD118 but can be used with Coyote pin systems or other locks in combination with the Integrator. Can be glued to the lock in any offset position for fabrication into socket. Eliminates the need for offset components. For lamination or thermoforming. 265 lb. weight limit.

Untitled design (84).png

C53TS | Offset 3 Prong

Greater Offset

Strong bendable arms for adjustability

Anatomical knee center positioning for long amputations.

C53TS-Offset-3-Prong---Aug2024-(25)-Clean-Shaddow-rgb-667x500-png.png

CD103PFF | Pediatric Fast Four Connector

CD103PFF-PediatricFastFourConector-200X142.png

Pediatric 4-hole connector that keys directly onto the center of the lock. 100 lb. weight limit.

forcier3-200x165.jpg

CD103PAF | Pediatric Alignable Connector

CD103PAF-PediatricAlignableFourConector-200X142.png

Can be used to offset the connector by up to 0.25". 100 lb. weight limit.

CD103PAF-OffSet-33-200x133.jpg
119SC Test Socket Connector (4).png
119SC Test Socket Connector (2) clean.png

CD119SC | Test Socket Connector

Economical, cost-effective, easy way to glue on connector designed specifically for Vivac check sockets. Connects to standard four-hole componentry with our new high-strength bridging design. Bonds well with Coyote Quik Adhesive. 11/16”height, 2 3/4” diameter, reusable.

The Test Socket Connector, when glued onto a test socket is for static fitting only.
The Test Socket Connector, when glued and reinforced with rigid fiberglass tape can be used in a dynamic fitting under the supervision of a practitioner in parallel bars.
The Test Socket Connector is not to be used outside of the facility.

CD106-Alignment-Coupler.png

CD106 | Alignment Coupler

Offset for ML and AP of 0.64". Easily installs on the four-hole connector. Easy to adjust with a 3mm wrench. For fitting purposes only. 265 lb. weight limit.

Untitled design (85).png

CD103AF | Alignable Connector

Alignable Connector being adjusted in transfer jig

CD111 | One-Shot Connector

One-Shot Connector being glued in place off set

Helpful Videos

airlock without valve body-1
01:27
airlock without pin-1
00:43
Coyote-Lock-Build-Height-Sheet-324x250.jpg
bottom of page